S9S08RN32W1MLC NXP
Available
S9S08RN32W1MLC NXP
• 8-Bit S08 central processor unit (CPU) – Up to 20 MHz bus at 2.7 V to 5.5 V across temperature range of -40 °C to 125 °C – Supporting up to 40 interrupt/reset sources – Supporting up to four-level nested interrupt – On-chip memory – Up to 60 KB flash read/program/erase over full operating voltage and temperature – Up to 256 byte EEPROM with ECC; 2-byte erase sector; EEPROM program and erase while executing code from flash – Up to 4096 byte random-access memory (RAM) – Flash and RAM access protection • Power-saving modes – One low-power stop mode; reduced power wait mode – Peripheral clock enable register can disable clocks to unused modules, reducing currents; allows clocks to remain enabled to specific peripherals in stop3 mode • Clocks – Oscillator (XOSC) - loop-controlled Pierce oscillator; crystal or ceramic resonator – Internal clock source (ICS) - containing a frequencylocked-loop (FLL) controlled by internal or external reference; precision trimming of internal reference allowing 1% deviation across temperature range of 0 °C to 70 °C and -40 °C to 85 °C, 1.5% deviation across temperature range of -40 °C to 105 °C, and 2% deviation across temperature range of -40 °C to 125 °C; up to 20 MHz • System protection – Watchdog with independent clock source – Low-voltage detection with reset or interrupt; selectable trip points – Illegal opcode detection with reset – Illegal address detection with reset • Development support – Single-wire background debug interface – Breakpoint capability to allow three breakpoints setting during in-circuit debugging – On-chip in-circuit emulator (ICE) debug module containing two comparators and nine trigger modes • Peripherals – ACMP - one analog comparator with both positive and negative inputs; separately selectable interrupt on rising and falling comparator output; filtering – ADC - 16-channel, 12-bit resolution; 2.5 µs conversion time; data buffers with optional watermark; automatic compare function; internal bandgap reference channel; operation in stop mode; optional hardware trigger – CRC - programmable cyclic redundancy check module – FTM - three flex timer modulators modules including one 6-channel and two 2-channel ones; 16-bit counter; each channel can be configured for input capture, output compare, edge- or centeraligned PWM mode – IIC - One inter-integrated circuit module; up to 400 kbps; multi-master operation; programmable slave address; supporting broadcast mode and 10-bit addressing – MTIM - Two modulo timers with 8-bit prescaler and overflow interrupt – RTC - 16-bit real timer counter (RTC) – SCI - three serial communication interface (SCI/ UART) modules optional 13-bit break; full duplex non-return to zero (NRZ); LIN extension support – SPI - one 8-bit and one 16-bit serial peripheral interface (SPI) modules; full-duplex or single-wire bidirectional; master or slave mode – TSI - supporting up to 16 external electrodes; configurable software or hardware scan trigger; fully support freescale touch sensing software library; capability to wake MCU from stop3 mode• Input/Output – Up to 55 GPIOs including one output-only pin – Two 8-bit keyboard interrupt modules (KBI) – Two true open-drain output pins – Eight, ultra-high current sink pins supporting 20 mA source/sink current • Package options – 64-pin LQFP – 48-pin LQFP – 32-pin LQFP
• 8-Bit S08 central processor unit (CPU) – Up to 20 MHz bus at 2.7 V to 5.5 V across temperature range of -40 °C to 125 °C – Supporting up to 40 interrupt/reset sources – Supporting up to four-level nested interrupt – On-chip memory – Up to 60 KB flash read/program/erase over full operating voltage and temperature – Up to 256 byte EEPROM with ECC; 2-byte erase sector; EEPROM program and erase while executing code from flash – Up to 4096 byte random-access memory (RAM) – Flash and RAM access protection • Power-saving modes – One low-power stop mode; reduced power wait mode – Peripheral clock enable register can disable clocks to unused modules, reducing currents; allows clocks to remain enabled to specific peripherals in stop3 mode • Clocks – Oscillator (XOSC) - loop-controlled Pierce oscillator; crystal or ceramic resonator – Internal clock source (ICS) - containing a frequencylocked-loop (FLL) controlled by internal or external reference; precision trimming of internal reference allowing 1% deviation across temperature range of 0 °C to 70 °C and -40 °C to 85 °C, 1.5% deviation across temperature range of -40 °C to 105 °C, and 2% deviation across temperature range of -40 °C to 125 °C; up to 20 MHz • System protection – Watchdog with independent clock source – Low-voltage detection with reset or interrupt; selectable trip points – Illegal opcode detection with reset – Illegal address detection with reset • Development support – Single-wire background debug interface – Breakpoint capability to allow three breakpoints setting during in-circuit debugging – On-chip in-circuit emulator (ICE) debug module containing two comparators and nine trigger modes • Peripherals – ACMP - one analog comparator with both positive and negative inputs; separately selectable interrupt on rising and falling comparator output; filtering – ADC - 16-channel, 12-bit resolution; 2.5 µs conversion time; data buffers with optional watermark; automatic compare function; internal bandgap reference channel; operation in stop mode; optional hardware trigger – CRC - programmable cyclic redundancy check module – FTM - three flex timer modulators modules including one 6-channel and two 2-channel ones; 16-bit counter; each channel can be configured for input capture, output compare, edge- or centeraligned PWM mode – IIC - One inter-integrated circuit module; up to 400 kbps; multi-master operation; programmable slave address; supporting broadcast mode and 10-bit addressing – MTIM - Two modulo timers with 8-bit prescaler and overflow interrupt – RTC - 16-bit real timer counter (RTC) – SCI - three serial communication interface (SCI/ UART) modules optional 13-bit break; full duplex non-return to zero (NRZ); LIN extension support – SPI - one 8-bit and one 16-bit serial peripheral interface (SPI) modules; full-duplex or single-wire bidirectional; master or slave mode – TSI - supporting up to 16 external electrodes; configurable software or hardware scan trigger; fully support freescale touch sensing software library; capability to wake MCU from stop3 mode• Input/Output – Up to 55 GPIOs including one output-only pin – Two 8-bit keyboard interrupt modules (KBI) – Two true open-drain output pins – Eight, ultra-high current sink pins supporting 20 mA source/sink current • Package options – 64-pin LQFP – 48-pin LQFP – 32-pin LQFP
Please make sure your contact information is correct. Your message will be sent directly to the recipient(s) and will not be publicly displayed. We will never distribute or sell your personal information to third parties without your express permission.
