SAK-TC264D-40F200W BC Infineon
The TC26x product family has the following features: • High Performance Microcontroller with two CPU cores • One 32-bit super-scalar TriCore CPUs (TC1.6P), having the following features: – Superior real-time performance – Strong bit handling – Fully integrated DSP capabilities – Multiply-accumulate unit able to sustain 2 MAC operations per cycle – up to 200 MHz operation at full temperature range – up to 120 Kbyte Data Scratch-Pad RAM (DSPR) – up to 32 Kbyte Instruction Scratch-Pad RAM (PSPR) – 16 Kbyte Instruction Cache (ICACHE) – 8 Kbyte Data Cache (DCACHE) • Power Efficient scalar TriCore CPU (TC1.6E), having the following features: – Binary code compatibility with TC1.6P – up to 200 MHz operation at full temperature range – up to 72 Kbyte Data Scratch-Pad RAM (DSPR) – up to 16 Kbyte Instruction Scratch-Pad RAM (PSPR) – 8 Kbyte Instruction Cache (ICACHE) – 0.125Kbyte Data Read Buffer (DRB) • Lockstepped shadow core for TC1.6P • Multiple on-chip memories – All embedded NVM and SRAM are ECC protected – up to 2.5 Mbyte Program Flash Memory (PFLASH) – up to 96 Kbyte Data Flash Memory (DFLASH) usable for EEPROM emulation – 0 Kbyte Memory (LMU) – BootROM (BROM) • 48-Channel DMA Controller with safe data transfer • Sophisticated interrupt system (ECC protected) • High performance on-chip bus structure – 64-bit Cross Bar Interconnect (SRI) giving fast parallel access between busmasters, CPUs and memories – 32-bit System Peripheral Bus (SPB) for on-chip peripheral and functional units – One bus bridge (SFI Bridge) • Safety Management Unit (SMU) handling safety monitor alarms • Memory Test Unit with ECC, Memory Initialization and MBIST functions (MTU) • Hardware I/O Monitor (IOM) for checking of digital I/O • Versatile On-chip Peripheral Units – Four Asynchronous/Synchronous Serial Channels (ASCLIN) with hardware LIN support (V1.3, V2.0, V2.1 and J2602) up to 50 MBaud – Four Queued SPI Interface Channels (QSPI) with master and slave capability upto 50 Mbit/s – High Speed Serial Link (HSSL) for serial inter-processor communication up to 320Mbit/s
– Two serial Micro Second Bus interfaces (MSC) for serial port expansion to external power devices – One MultiCAN+ Module with 5 CAN nodes and 256 free assignable messageobjects for high efficiency data handling via FIFO buffering and gateway data transfer – 6 Single Edge Nibble Transmission (SENT) channels for connection to sensors – One FlexRayTMmodule with 2 channels (E-Ray) supporting V2.1 – One Generic Timer Module (GTM) providing a powerful set of digital signal filteringand timer functionality to realize autonomous and complex Input/Output management – One Capture / Compare 6 module (Two kernels CCU60 and CCU61) – One General Purpose 12 Timer Unit (GPT120) – Three channel Peripheral Sensor Interface conforming to V1.3 (PSI5) – Peripheral Sensor Interface with Serial PHY (PSI5-S) – Inter-Integrated Circuit Bus Interface (I2C) conforming to V2.1 – IEEE802.3 Ethernet MAC with RMII and MII interfaces (ETH) • 8-bit Standby Controller (TC2x_SCR) – Two 8-bit timers – One 16-bit timer – Timer 2 Capture Compare Unit – Real Time Clock – Universal Asynchronous Receiver/Transmitter – High Speed Synchronous Serial Interface – Wake-up CAN Filter • Versatile Successive Approximation ADC (VADC) – Cluster of 4 independent ADC kernels – Input voltage range from 0 V to 5.5V (ADC supply) • Delta-Sigma ADC (DSADC) – Three/Four channels • Digital programmable I/O ports • On-chip debug support for OCDS Level 1 (CPUs , DMA, On Chip Buses) • Dedicated Emulation Device chip available (ED) – multi-core debugging, real time tracing, and calibration – Aurora Gigabit Trace Port (AGBT) on some variants (See below) – four/five wire JTAG (IEEE 1149.1) or DAP (Device Access Port) interface • Power Management System and on-chip regulators • Clock Generation Unit with System PLL and Flexray PLL • Embedded Voltage Regulator
Please make sure your contact information is correct. Your message will be sent directly to the recipient(s) and will not be publicly displayed. We will never distribute or sell your personal information to third parties without your express permission.